Who has Cuda 250 S/Map
Who has Cuda 250 S/Map
Picked up my CUDA 250 S/Map last night and practiced some functions
in the house, pretty impressive with overall operation, any one have this
unit installed ??
--tmoore
in the house, pretty impressive with overall operation, any one have this
unit installed ??
--tmoore
QUESTIONS: how do you rig the two wires that come up from
the inside of the yak. one for power and one for TD. On my setup
they end up on one connector right at the unit. I have an idea that
when not in use or running baits out in a BTB setting that you just
let the wire hang.
thoughts on wire routing install.
-tmoore
the inside of the yak. one for power and one for TD. On my setup
they end up on one connector right at the unit. I have an idea that
when not in use or running baits out in a BTB setting that you just
let the wire hang.
thoughts on wire routing install.
-tmoore
- pitontheprowl
- TKF 2000 club
- Posts: 2833
- Joined: Wed Jun 22, 2005 9:52 am
- Location: San Antonio
- Contact:
-
- TKF 1000 Club
- Posts: 1003
- Joined: Fri Apr 28, 2006 3:22 am
- Location: Missouri City Red Wilderness T160i
planohog wrote:QUESTIONS: how do you rig the two wires that come up from
the inside of the yak. one for power and one for TD. On my setup
they end up on one connector right at the unit. I have an idea that
when not in use or running baits out in a BTB setting that you just
let the wire hang.
thoughts on wire routing install.
-tmoore
That is when you drill a hole on your kayak . . .
- dlaws60600
- Posts: 328
- Joined: Sat Dec 16, 2006 12:53 pm
- Location: Houston TX
cuda 250
Got 1 but whats the best batt pack for it, and where can i buy??
I have the 8pack and I tested for 3 hours worked great, last
voltage reading was 10.62, I ran the back lights for most of that time
as well.
The thing that is bothering me is the wire bundle has two round cables.
It it was one large one well then you get a large rubber grommett to fit.
I guess I just anwsered my own question. Make the two wire bundle one,
find a good fit grommett ( have to cut the grommet to get a good fit ).
Im also trying to figure out how I can have this mounted in two places,
one when in tadem, and one when solo.
voltage reading was 10.62, I ran the back lights for most of that time
as well.
The thing that is bothering me is the wire bundle has two round cables.
It it was one large one well then you get a large rubber grommett to fit.
I guess I just anwsered my own question. Make the two wire bundle one,
find a good fit grommett ( have to cut the grommet to get a good fit ).
Im also trying to figure out how I can have this mounted in two places,
one when in tadem, and one when solo.
- Barnacle Brain
- Posts: 194
- Joined: Fri Dec 02, 2005 1:31 pm
- Location: Tomball,You can take the boy outta Fla but you can't take Fla outta the boy
- Fla-Fish
- TKF 8000 Club
- Posts: 8389
- Joined: Tue Apr 05, 2005 2:49 pm
- Location: N Houston. Waiting for the "Running of the Bulls"
Barnacle Brain wrote:be careful with cable end. salt will corrode and ruin it. had to replace my cable last week. mightuse grease to keep it watertight.
I put a waterproof shutoff switch on the outside of my battery box to shut of power to the "cable end" when I did not have it connected. I read that juice in the disconnected cable will corrode the connection alot faster. It causes "electrolysis" and corodes quick. There is also a tube of special grease that I kept the end covered with to prevent it. I forget what they call it. It's made for battery connections to protect them. Almost 2 yrs no problems with my Cuda 240.
Tim what did you pay for the Cuda 250. Thinking about upgrading for back bays and marsh mazes. And keeping the 240 for just offshore.
- dlaws60600
- Posts: 328
- Joined: Sat Dec 16, 2006 12:53 pm
- Location: Houston TX
Inside hull td mounting
How do u mount the transducer on the inside of the hull with the foam block and the vasaline????